The short answer
A radiator that is cold in one place is telling you something. Cold at the top often means trapped air, while cold at the bottom often means debris in the system. Cold all over may point to a stuck valve or a wider heating fault.
These are common patterns, not a diagnosis. A heating engineer can confirm the cause, because systems differ.
Cold at the top
If the top is cold and the bottom is hot, air is probably trapped inside. Air rises and blocks the hot water from filling the top. Bleeding the radiator usually fixes this, since it lets the air out.
Follow these steps, because the order matters.
- Switch off the heating and let the radiator cool.
- Hold a cloth under the bleed valve.
- Turn the valve slowly with a radiator key until you hear a hiss.
- Close the valve as soon as water appears.
- Check the boiler pressure afterwards.
Bleeding lets out a little water, so system pressure can drop. Our boiler pressure guide explains the checks. Always follow your boiler manual when you top up, because each boiler differs.
Cold at the bottom
If the bottom is cold and the top is hot, something may be blocking the flow. Sludge and rust can settle at the bottom of a radiator. The effect builds over time, while some radiators suffer more than others.
A heating engineer can flush the system or fit a filter to catch debris. Ask what the engineer recommends for your system, since needs differ. Our radiator and central heating service covers flushing and valve work.
Cold all over
A radiator that stays cold across its whole face has a different set of causes, although some look alike.
- A stuck valve. The pin in the valve can jam shut.
- A closed lockshield valve. The valve at the other end may be closed.
- Poor balance. The water may be going to other radiators first.
- A system fault. The pump, the controls or the boiler may be at fault.
If every radiator is cold, check the boiler first. Look for an error code or a pressure problem. Our guide to boiler fault codes explains what to do. Never open the boiler casing, because gas parts sit inside.
Warm at the edges, cold in the middle
A cold patch in the middle of a radiator often points to sludge. It can also mean the radiator is partly blocked. This case needs a flush rather than a bleed, since air is not the cause.
Hot water and heating together
If you have heat but no hot water, the fault may be elsewhere. Our guide to no hot water: what to check goes through the steps. The hot water cylinder cost guide covers a failing cylinder.
Stopping a leak at a radiator
A drip at a valve needs quick action. Close the valve if you can, and wipe up the water. If the leak is serious, turn off the water at the stop tap. Our guide to where your stop tap is likely to be helps. Then switch off the heating, because the system may lose water, and ask a plumber to attend.
Repair or replace?
Some radiators are not worth saving. MyJobQuote and TradeMatch give about £150 to £350 to replace a radiator like for like, fitted. MyJobQuote gives about £150 to £200 for the North of England and the Midlands. These are guides, not our prices, so ask for a quote.
If the whole system is old, the boiler may need attention too. Our new boiler cost guide sets out typical prices. Landlords have extra duties, so see our landlord plumbing checklist.
Carbon monoxide is a separate risk from heating faults. HSE strongly recommends an alarm, and our guide to carbon monoxide at home explains the signs. Before you choose an engineer, read how to choose a plumber.
Frequently asked questions
Should I bleed all my radiators?
Bleed any that feel cold at the top. Start with the radiator nearest the boiler, then work outwards, because that keeps the order simple.
Why do my radiators take long to warm up?
Air, sludge or poor balance can slow them, although a heating engineer must check which applies.
Is it safe to bleed a radiator myself?
Yes, in most homes, if you switch off the heating first and follow the steps. Check the boiler pressure afterwards.
Ask a heating engineer
Our radiator and central heating service and boiler repair service take requests through the online form. Browse all our services or the areas we cover. Add your town and a short description, because that helps an engineer get back to you.
In Northampton, see plumbers in Northampton. Around Earls Barton, see plumbers in Earls Barton. In Burton Latimer, see plumbers in Burton Latimer. Near Rothwell, see plumbers in Rothwell. These pages list local details, since coverage varies from town to town.
We cover Northampton and a 30-mile radius, while the request form is open 24/7. Our engineers are Gas Safe registered.
Last updated 16 November 2026
Related Services
Radiator & Central Heating
Radiator and central heating help across Northampton and towns within 30 miles. Tell us which radiators stay cold, because the position points to the cause.
Learn more →Boiler Repair & Installation
Boiler repair and installation across Northampton and towns within 30 miles. Engineers on gas jobs are Gas Safe registered, because the law requires it.
Learn more →