Skip to main content
Updated 2 October 2026

Water Tank & Cylinder Northampton

No hot water or a leaking cylinder? Tell us what you see and what type you have, because the type decides the fix.

Request a Quote
The request form is open 24/7. Mark urgent jobs as urgent.

Request a Quote — Water Tank & Cylinder

Gas Safe Registered G3 Qualified 24/7 Enquiry Form 32 Towns Covered
Water Tank & Cylinder in Northampton

A hot water cylinder stores heated water for your taps and showers. Vented cylinders use a loft tank, while unvented ones run from the mains. Engineers are G3 qualified for unvented work.

Vented and unvented cylinders

A vented cylinder gets its water from a tank in the loft. Gravity sets the pressure, so showers can feel weak. However, an unvented cylinder connects to the mains and gives stronger flow.

Unvented cylinders need extra safety parts and a qualified installer, because they hold hot water under pressure. Approved Document G (G3) expects a competent person to fit them. The work must go through building control or a competent person scheme, as GOV.UK explains.

Engineers on this service are G3 qualified for unvented hot water. Ask what certificates you will receive when the job ends, since they matter for unvented work.

Common cylinder faults

Lukewarm water can mean a faulty thermostat or a failed immersion heater. Hot water that runs out fast may mean the cylinder is too small. A leak from the cylinder itself usually means a replacement, although a leaking joint nearby may be an easy fix.

If a cylinder leaks, turn off the supply at the stop tap and switch off the immersion heater. Then send a request marked urgent while you wait. Our first 10 minutes guide covers the steps.

What a new cylinder costs

BestBuilders gives £750 to £1,400 for a vented copper cylinder and £900 to £3,000 for an unvented one. Rosebourne Plumbing gives £800 to £1,500 and £1,500 to £3,000. Both guides exclude VAT.

These are guides, not our prices. Send a request for an exact quote.

Where we cover

We cover Northampton and towns within 30 miles. Local pages cover plumbers in Northampton, plumbers in Rushden and plumbing in Higham Ferrers, while you can also see plumbers in Irthlingborough and our full list of areas.

If your hot water comes from a combi boiler, see boiler repair instead, since a combi has no cylinder. A leaking pipe near the cylinder needs burst pipe repair.

What This Service Covers

  • Diagnosis of cylinder and immersion heater faults
  • Vented and unvented cylinder replacement
  • Cold water tank repair or replacement
  • Immersion heater replacement
  • Expansion vessel and pressure relief valve checks
  • G3 qualified engineers for unvented cylinders

How It Works

1

Describe the problem

Say if the water is cold, lukewarm or leaking. Tell us the type of cylinder if you know it, since parts differ.

2

Your request is passed on

Your request goes to an engineer, who can get back to you with next steps. Mark it urgent if water is leaking, because a leak can spread quickly.

3

Repair or replace

The engineer explains whether a repair or a new cylinder makes sense. Ask for both prices, since the age of the cylinder matters.

4

Commission the work

Unvented cylinders need notification under Building Regulations. Ask who handles it, because the notification is a legal step.

Frequently Asked Questions

What is the difference between vented and unvented cylinders?
A vented cylinder takes water from a loft tank and relies on gravity. An unvented cylinder connects to the mains and gives higher pressure but needs extra safety parts.
Why does my hot water run out quickly?
The thermostat may be stopping the cylinder from heating fully, or the immersion element may have failed. The cylinder may also be too small for your household.
Do I need a certificate for a new cylinder?
For unvented cylinders, yes. Approved Document G expects a competent person to fit them and the work to go through building control or a competent person scheme. The engineers are G3 qualified.
Why is my hot water only lukewarm?
A faulty thermostat or a partly failed immersion element is the usual cause. An engineer can test both.
How much does a new cylinder cost?
BestBuilders gives £750 to £1,400 vented and £900 to £3,000 unvented. Rosebourne Plumbing gives £800 to £1,500 and £1,500 to £3,000. Both exclude VAT and are guides, not our prices.
What should I do if the cylinder leaks?
Turn off the supply at the stop tap and switch off the immersion heater. Send a request and mark it urgent.

Related Services

Related Guides

Request a quote

Need Water Tank & Cylinder in Northampton?

The request form is open 24/7. Engineers on gas jobs are Gas Safe registered.

Request a Quote — Water Tank & Cylinder